How to Fix a Leaking Roof in Winter (Flat Roofs, Gutters and Flashings)

Amelia ParkerUpdated

Roof leaks have a habit of showing up on the worst night of the year. Frost lifts old felt, storms drive rain under laps and flashings, and blocked gutters back up and spill down the wall. The good news is that most small roof and gutter leaks can be sealed by a competent DIYer, even in cold, wet weather, as long as you use products made to go on in those conditions. This guide covers how to find the leak, how to seal flat roofs, gutters and flashings, and where the line is between a fix you can do and a job for a roofer.

Find the leak before you seal anything

Water rarely enters where it drips. It runs along a batten, a felt lap or a joist and shows up on the ceiling a metre or more from the actual hole. So before you buy anything, work out where it is really getting in. Check the roof on a dry day and look for the usual suspects: splits and blisters in flat-roof felt, lifted or slipped tiles and slates, gaps in the mortar or lead around a chimney, and gutters and downpipes that are blocked or leaking at the joints. Inside the loft, follow the water stain back up to the highest wet point, which is usually closer to where it enters.

Common winter roof leaks and how to seal them

Where it leaks Likely winter cause How to seal it
Flat felt or asphalt roof Splits, blisters and tired laps opened by frost Clean and dry, seal with an all-weather bitumen compound, reinforce splits with scrim, then coat
Gutter and downpipe joints Movement and debris opening the seals Clear the gutter, then seal the joint with a flexible roof and gutter sealant
Chimney, abutment and step flashings Lead lifted or mortar cracked by weather Reseal with flashing tape or a lead sealant
Whole tired flat roof General weathering, coating worn through Recoat with a UV-stable roof coating membrane
Split downpipe or pipe (temporary) Frozen water splitting the pipe Wrap with self-fusing repair tape as a stopgap, then replace
Match the product to the surface and the weather. In frost or rain, reach for the solvent-based options.

Can you repair a roof in winter or wet weather?

Yes, if you pick the right product. This is the single most useful thing to understand about winter roofing. Water-based bitumen emulsions are best kept for dry spells, because rain or frost before they cure can wash them off or spoil the finish. Solvent-based bitumen products are made for wet, cold conditions, and Bond-It's own guidance is to use its All Weather Roofing Compound where the threat of frost or rain rules out an emulsion. It can be applied in frost or rain, it will not crack in the cold or flow in the sun, and it works on mastic asphalt, roofing felt, corrugated iron, fibre cement, slates, lead, copper, tin and zinc.

How to fix a flat roof leak

Flat roofs are the most common DIY roof repair, and cold weather is when they tend to fail. Work on a dry patch of daylight if you can, even in winter, and take your time on the prep, because that is what makes the seal last.

  1. Clean and dry the area. Brush off grit, moss and loose chippings, and get the surface as dry as conditions allow. A sound, clean surface is what the coating grips.
  2. Prime porous or dusty surfaces. On old, absorbent felt or bare fibre cement, a coat of bitumen primer first improves adhesion and stops the compound being sucked in.
  3. Seal splits and blisters. Work the bitumen compound well into the split with a brush. For anything more than a hairline, bed a piece of reinforcing scrim or membrane into the wet compound and coat over the top, so the repair bridges the gap rather than just filling it.
  4. Coat the area, or the whole roof. For a roof that is generally tired rather than split in one spot, a full recoat gives a fresh waterproof skin. Bond-It Sealacryl roof coating membrane is a UV-stable, flexible membrane that resists ponding water, the standing water that collects on flat roofs and finds every weak point.

How to fix a leaking gutter

A gutter that overflows in winter is usually blocked, not broken, so clear it first. Scoop out the leaves and silt, flush it through, and check the fall runs toward the downpipe. Once it is clear and drying, seal any joints that are weeping. A flexible sealant matters here, because gutters expand and contract with temperature and a rigid filler cracks at the next frost. Bond-It Roof and Gutter Sealant is a polymer-reinforced sealant and adhesive that stays flexible and bonds to metal, plastic, stone, timber, brick, bitumen and asphalt, so it seals both modern uPVC guttering and older metal systems. Get the joint as clean and dry as you can, apply the sealant into and over it, and tool it to a smooth, continuous bead.

Flashings, chimneys and laps

The join between the roof and anything that sticks through it, a chimney, a parapet, an abutment wall, is where a lot of leaks start, because lead lifts and pointing cracks over the years. For a quick, reliable reseal, self-adhesive flashing tape presses over the joint and bonds to the roof and the wall, and its lead-coloured finish keeps it discreet. Prime dusty or porous surfaces first for the best bond, and press the tape down firmly with a roller or the back of a filling knife so it keys right in.

Emergency roof repair: temporary fixes

Sometimes you just need to stop the water tonight and repair it properly when the weather breaks. A tarpaulin lapped over the ridge and weighted, never nailed through sound covering, buys you time on a pitched roof. For a split downpipe or a weeping pipe joint, self-fusing rescue tape stretches and bonds to itself to hold back water as a stopgap. Treat these as holding measures, then go back and do the permanent repair with the right sealant or coating once you can.

When to call a roofer

Know your limits. A single-storey flat roof, a ground-floor gutter or a low lean-to are fair DIY territory with the right kit and a stable ladder or tower. A steep or high pitched roof, anything involving structural timber, spreading damp in the loft, or a leak you simply cannot find is a job for a professional with the access equipment and the experience to work safely. Falls from height are the biggest risk in this whole guide, so if the access is not safe, stop and make the call.

Get set for winter

The trick with winter roofing is having the right products in the van before the storm, not after. An all-weather bitumen compound and a primer for emergency flat-roof repairs, a flexible roof and gutter sealant for the guttering, flashing tape for the joints, and a roof coating for a proper recoat when the weather allows. You will find all of them, along with the rest of the cold-weather range, in our winter essentials collection.

Frequently asked questions

Can you repair a roof in winter or wet weather?

Yes, if you use the right product. Water-based bitumen emulsions should not be used when frost or rain is likely, because they can wash off before they cure. Solvent-based bitumen products such as an all-weather roofing compound are made to go on in frost or rain, which is why they are the sensible choice for a winter repair.

How do I temporarily stop a roof leak?

Get water out of the way first. On a pitched roof, lap a tarpaulin over the ridge and weight it down rather than nailing through good covering. On a split downpipe or pipe joint, self-fusing rescue tape holds back water as a stopgap. Both are holding measures, so go back and make a permanent repair when the weather allows.

What is the best product to seal a flat roof?

For spot repairs to splits and blisters in frost or rain, an all-weather bitumen compound worked into the split, reinforced with scrim on anything larger. For a whole tired roof, a UV-stable roof coating membrane that resists ponding water gives a fresh waterproof skin. Prime porous or dusty surfaces first for a lasting bond.

How do I fix a leaking gutter joint?

Clear the gutter of leaves and silt so it drains, then get the joint as clean and dry as you can. Apply a flexible roof and gutter sealant into and over the joint and tool it to a smooth bead. Flexibility matters because gutters move with temperature, and a rigid filler will crack at the next cold snap.

Why does my roof only leak in heavy rain or winter?

A small gap can shed light rain but let heavy, wind-driven rain past, so the leak only shows in a downpour. In winter, frost lifts old felt and cracks pointing, and blocked gutters back up, so faults that coped in summer start letting water in. It usually means a worn lap, flashing or coating that needs sealing.

Can I paint a bitumen coating on in the cold?

A solvent-based bitumen roofing compound is made to be applied in frost or rain and will not crack in the cold or flow in the heat once on. A water-based bitumen emulsion is not the right choice when frost or rain is likely, so keep it for a dry spell. Check which type you have and match it to the weather.

How do I fix a leak around a chimney or flashing?

Reseal the joint between the roof and the upstand. Self-adhesive flashing tape presses over the joint and bonds to both surfaces for a quick, discreet reseal, or a lead sealant can be worked into gaps in existing lead and pointing. Prime dusty surfaces first and press the tape down firmly so it keys in.

When should I call a roofer instead of fixing it myself?

A low flat roof, a ground-floor gutter or a lean-to are reasonable DIY jobs with the right products and safe access. Call a professional for a steep or high pitched roof, anything structural, spreading damp in the loft, or a leak you cannot locate. Working at height is the real risk, so if the access is not safe, stop.

Leave a comment

Please note, comments must be approved before they are published