How to Get Rid of Black Mould and Condensation (Winter Guide)

Amelia ParkerUpdated

Every autumn the same thing happens. The heating goes on, the windows stay shut, and within a few weeks black spots appear in the corner of a bedroom ceiling or along the bathroom sealant. That black mould is almost always the visible end of a condensation problem, so wiping it off treats the symptom and not the cause. This guide covers how to remove black mould properly, how to stop the condensation feeding it, and how to tell when the damp is coming from somewhere else entirely.

Why mould appears in winter

Warm air holds moisture. Cooking, showering, drying clothes and just breathing all put water vapour into the air of a house. In summer that vapour drifts out through open windows. In winter the house is sealed up and the air is warmer inside than out, so when that warm, damp air meets a cold surface, a window, a cold external wall, the back of a wardrobe, it cools and drops its moisture as condensation. Leave that surface damp for long enough and mould spores, which are in the air everywhere, settle and grow. That is why mould turns up in the coldest, least ventilated spots: behind furniture on outside walls, in window reveals, and around bathroom and kitchen edges.

Where winter mould shows up, and why

Where Why it happens The real fix
Bedroom ceiling corners and window reveals Cold external corners, warm damp air, little airflow Remove the mould, add ventilation, keep low background heat
Behind wardrobes and beds on outside walls Furniture traps a cold, still pocket of air Pull furniture off the wall, remove mould, improve airflow
Bathroom sealant and grout Constant moisture with poor extraction Remove mould, run the extractor, reseal with an anti-mould silicone
Window frames and glass Coldest surface in the room, hits dew point first Wipe daily, use trickle vents, reduce moisture at source
Outside face of a wall, patchy and spreading Not condensation, this is penetrating damp from driving rain Treat the cause outside with a breathable masonry waterproofer
Most winter mould is condensation on a cold surface. The last row is the exception worth knowing about.

How to get rid of black mould

Treat mould as a job worth doing once, properly. Loose spores get into the air when you disturb it, so open a window, wear rubber gloves and an FFP2 mask, and keep anyone with asthma or a chest condition out of the room while you work. Black mould is worth removing promptly, and anyone with breathing problems should take it seriously rather than live with it.

  1. Do not dry-brush it. Scrubbing dry mould flings spores across the room. Wet it first.
  2. Use a proper mould remover, not just bleach. Household bleach often lightens the stain while leaving the root in porous plaster or sealant, so it grows back. A dedicated mould remover kills the growth as well as clearing the mark. Spray it on, and give it time to work rather than wiping straight away.
  3. Let it dwell, then wipe. Leave the product on the surface for the time on the label so it can kill the mould, then wipe away with a cloth and bin the cloth. On heavy growth, a second application beats one hard scrub.
  4. Deal with the source. If you skip the ventilation and heating changes below, the mould comes straight back. Removal buys you a clean surface; airflow keeps it clean.

For mould on indoor walls, ceilings and window reveals, use a mould remover labelled for indoor use and follow its dwell time. For mould, mildew and lichen on outside walls, render, roofs and patios, Bond-It Mould Stop is formulated for exterior surfaces. Where the problem keeps coming back in a bathroom or kitchen, strip the old bead of sealant and reseal with an anti-mould silicone sealant, which holds a fungicide in the cured bead so the joint resists regrowth far longer than a standard sanitary silicone. Bond-It Xtreme is guaranteed mould-free for up to 10 years.

Mould on a bedroom ceiling

Bedrooms are where winter mould shows up most, usually in the corner where the ceiling meets an outside wall. Overnight, everyone sleeping in a closed room breathes moisture into the air, and that corner is the coldest surface it reaches. To fix it, clean the mould off as above, leave the window trickle vent open overnight, keep the room at a low, steady heat rather than letting it go cold, and leave the door ajar so air can circulate. If the same corner keeps coming back, check the loft above it: missing or slipped insulation over that corner makes the ceiling colder and is a common cause.

Best mould remover: bleach or a dedicated remover?

Bleach has a place on hard, non-porous surfaces like glazed tile and glass, where it kills what it touches. The trouble on plaster, painted walls and old sealant is that the mould roots sit below the surface, and bleach mostly bleaches the colour out of the top layer. You get a clean-looking wall for a few weeks, then the same spots return. A mould remover is formulated to stay on the surface and kill the growth rather than just discolour it, which is why it lasts longer on the surfaces where household mould actually grows.

How to stop condensation

You cannot beat mould long-term without cutting the condensation that feeds it. The aim is less moisture in the air and warmer surfaces for it to land on. None of this needs cranking the thermostat.

  • Ventilate where the moisture is made. Run the extractor fan during and after a shower or cooking, and keep the door shut so damp air goes out the fan, not into the hall and bedrooms.
  • Use trickle vents. The little vents on modern window frames are there to give a slow air change without a cold draught. Leave them open through winter.
  • Keep a low background heat. A house held at a steady, gentle warmth has warmer wall surfaces than one blasted hot in the evening and left to go stone cold overnight. Warmer surfaces sit further from dew point, so less water condenses.
  • Dry washing outside or in a vented room. A single load of wet washing drying on a rack puts litres of water into the air. Dry it outdoors, in a tumble dryer that vents out, or in a closed room with the window cracked.
  • Give outside walls some air. Pull wardrobes and beds a few centimetres off cold external walls so air can move behind them.
  • Lids on pans, and shut the bathroom door. Small habits that keep the worst of the steam contained.

Condensation on windows

Condensation on the inside of the glass is the clearest sign there is too much moisture in the room and the glass is the coldest surface it can find. Wipe it each morning so it does not run down and soak the frame, and work through the ventilation steps above.

Left to run down every morning, that water pools on the sill, which is why black mould on window sills and along the bottom of the frame is so common. Wipe sills dry, treat any black spots with a mould remover, and keep the trickle vents open. If the sealant around the frame has gone black, cut it out and reseal with an anti-mould silicone.

Condensation on the outside of windows

Condensation on the outside of the glass is different, and it is good news. It means the glazing is insulating so well that the outer pane stays cold enough for dew to form on it on a clear night. You see it most on modern, energy-efficient double and triple glazing on clear, still mornings. It clears itself as the day warms up and needs no action.

When it is damp, not condensation

Not every damp patch is condensation. If a wall is wet in a spreading patch rather than misted with tiny black spots, especially on a wall that takes the weather, you may have penetrating damp, where driving rain soaks through the masonry from outside. Condensation forms on the warm inside face of cold surfaces; penetrating damp works inward from the outside and often follows heavy rain. The fix for that is on the outside wall, not the inside. A breathable treatment like Bond-It Waterseal masonry waterproofer repels rain from brick and stone while still letting the wall breathe, so it keeps water out without trapping moisture in. Rising damp, which comes up from the ground in a tide mark near the skirting, is a separate problem that needs a damp-proof course.

Keep it away this winter

Once you have removed the mould and cut the moisture, the routine is simple: run the fans, leave the trickle vents open, keep a steady low heat, and wipe the windows on the coldest mornings. Reseal any bathroom or kitchen joints that have gone past cleaning with an anti-mould silicone. Do that and the corners stay clear through the worst of the winter. You will find exterior mould remover, anti-mould sealant and masonry waterproofer, along with the rest of the cold-weather range, in our winter essentials collection.

Frequently asked questions

What kills black mould permanently?

Nothing kills it forever on its own, because the spores are always in the air. What works is a two-part fix: kill and remove the existing growth with a proper mould remover, then stop the condensation that let it grow by ventilating, keeping a low background heat and cutting moisture at source. Remove the mould and fix the airflow, and it stays gone.

Is bleach or a mould remover better for black mould?

On glazed tile and glass, bleach is fine. On plaster, painted walls and sealant, a dedicated mould remover works better, because the mould roots below the surface and bleach mainly lightens the stain on top. That is why bleached mould tends to come back in a few weeks while a mould remover clears it for longer.

Why do I get condensation on my windows in winter?

The glass is usually the coldest surface in the room. Warm, moist indoor air from cooking, showering and drying clothes meets that cold glass, cools, and drops its moisture as water. It shows first on windows because they hit dew point before the walls do. Less moisture in the air and a little more warmth on the glass both reduce it.

Why is there condensation on the outside of my windows?

This is a sign of good glazing, not a fault. When the panes insulate well, the outer glass stays cold on a clear night and dew forms on it, exactly as it does on a car windscreen or the grass. It clears on its own as the morning warms up and needs no treatment.

How do I stop mould coming back in the bathroom?

Run the extractor fan during and after every shower with the door shut, wipe down the wettest surfaces, and reseal any joints where the mould has grown into the sealant. A fresh bead of anti-mould silicone, which carries a fungicide in the cured joint, resists regrowth far longer than a standard sealant that has already been colonised.

Is black mould dangerous?

Black mould is worth removing promptly. It can irritate the airways and make asthma and allergies worse, and prolonged exposure is best avoided, particularly for children, older people and anyone with a chest condition. Wear gloves and a mask when you remove it, ventilate the room, and treat the damp that caused it rather than living with repeated growth.

How do I stop condensation without heating the whole house?

Focus on moisture and airflow rather than temperature. Run extractor fans, open trickle vents, dry washing outside or in a vented dryer, keep lids on pans and pull furniture off cold walls. A steady, gentle background warmth helps more than short blasts of high heat, because it keeps wall surfaces above the point where water condenses.

What is the difference between condensation and damp?

Condensation forms on the inside face of cold surfaces when moist indoor air meets them, and shows as misting and small black mould spots in cold corners. Penetrating damp comes through the wall from outside after driving rain and shows as a spreading wet patch. Rising damp comes up from the ground as a tide mark near the floor. Each has a different fix, so identifying which one you have matters before you treat it.

Leave a comment

Please note, comments must be approved before they are published